Thank you for choosing an ARITECH security system. This manual explains how to use the ARITECH CD72 and CD95 series for every day use. There is a. A dual com polls to the monitoring station. What this means is every couple of minutes (depending on what it is set up for) it sends a signal to the monitoring. Hello, I want to integrate a solution based on PLUGWISE and an Aritech Alarm Central. I could successful connect a printer SERIAL RS

Author: Tojasida Mumuro
Country: Sierra Leone
Language: English (Spanish)
Genre: Health and Food
Published (Last): 12 June 2015
Pages: 50
PDF File Size: 17.59 Mb
ePub File Size: 14.49 Mb
ISBN: 694-3-35092-180-6
Downloads: 74013
Price: Free* [*Free Regsitration Required]
Uploader: Voodoojas

Numbering of the inputs Note: Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. If there is a short circuit in the 12 volt power supply, the voltage regulators in the supply together with the fuses will prevent serious damage to the system The 12 volt power supply will decrease sharply in the event of a short circuit.

Get out there and share your passion with others! Take some time to become familiar with the overview of the programming maps which can be found at the end of this manual.

Auxiliary power supply PG 4-wire bus of keypad or expander Figure Screw to close siren. You can also Private Message one of our Community Managers here.


The zone is Resistance Panel zone voltages Remote zone voltages Reaction on standby 3k5 – 6k2 2. Page 10 Supply only mains power to the control panel. Wij vragen u dus ook te reageren op een antwoord. The switching of these relays may cause electrical interference. Antwoorden worden ook per e-mail naar abonnees gestuurd.

Aritech TD8803 TD8412

Enter text from afitech You can read the announcement and access links to the revised policies here. This manual also for: Separate alarm and tamper connection Dual loop: Any programming changes made may not take effect until you exit programming mode. If a short circuit should occur, remove the 12 volt connections one by one.

So, what are you waiting for?

Before connecting, the cable between terminal 2 and terminal 10 should be removed! For most LEDs, however, a current of approximately 15 mA is sufficient. Supply only mains power to the control panel.

If there are several detectors place them in parallel and cable the zones as described in figure 1 or 2 see page 8. Keys on a CD30xx If this is not done, the system will be triggered as soon as it is switched on. In a keypad OA is the buzzer.

The reset is performed after the second entry of a code after an alarm. Programming for the sirens NB: No part of this publication may be reproduced, transmitted, stored in a retrieval system, or transmitted in any form, or by any means – electronic, photocopying, recording, or otherwise – without the prior written permission of SLC BV.


If dual loop is programmed, the letter T will appear next to the zone number to indicate the tamper section of the loop is open. Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel of niet mee geholpen bent!

Aritech ADVISOR CD Installation manual |

Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat aritch email groter is dan toegestaan bij uw provider. By pressing ‘print’ button you will print only current page. Every time power is removed from the system the control panel memorises its status. Connection of a relay or an LED on the output Ensure that there is a good earth for the alarm system.

Dual loop aeitech of a detector with latch Note: Close the tamper switches on the remote keypads, expanders and the control panel. Dual loop connection of a detector without memory Originally Posted by masterbates1 thanks, you say polls is this like a test call?

Uw handleiding is per email verstuurd.

Separate alarm and tamper connection U kunt hieronder aangeven waarom deze vraag ongepast is. Don’t show me this message again.