LM311N DATASHEET PDF

LMN Datasheet, LMN National Semiconductor Voltage Comparator Datasheet, buy LMN. The LM, LM, LM are voltage comparators that have low input currents. They are also designed to operate over a wide range of. Part, LMN. Category. Description, Voltage Comparators. Company, ST Microelectronics, Inc. Datasheet, Download LMN datasheet. Cross ref.

Author: Shaktigal Tygogore
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: Photos
Published (Last): 27 October 2008
Pages: 17
PDF File Size: 10.67 Mb
ePub File Size: 1.46 Mb
ISBN: 325-3-36256-219-1
Downloads: 73625
Price: Free* [*Free Regsitration Required]
Uploader: Sakasa

When not in use the pins 5 and 6 should be shorted as shown above. A sample circuit is shown below in which the Inverting Terminal is set to 2. Why is it not working in Multisim? An Emitter Output Circuit is shown below. I built a simple circuit using the LMN comparator.

LMN Datasheet(PDF) – STMicroelectronics

The transistor can also make the Load to be isolated from the system ground, so if you are looking for a Voltage comparator to drive loads of these specifications then this IC might be the right choice for you.

The pins 5 and 6 on the Op-amp are used to set the balance voltage if you want to manually adjust the DC-Offset voltage. You can refer the other possible circuits from the LM datasheet given at bottom.

The output is correct as seen on the scope. I just built the circuit in real life and it works exactly as I thought, putting GND on the strobe pin makes the output a constant state at Datahseeti.

  LIBRO ABZURDAH ONLINE PDF

The simplified schematics of the IC is shown below: Auto-suggest helps you quickly om311n down your search results by suggesting possible matches as you type. Message 5 of 5.

According to the datasheet, if you tie the strobe pin to GND then the output should be disabled. Most Active Software Boards: Any help is appreciated. You can note that the Output voltage stays high when pin 2 has higher voltage than pin 7 and vice versa.

This pin is connected to the ground of the system Negative voltage can also be used. Normally these pins are not used since the Input Offset itself is much better controlled. The simplified schematics of the IC is shown below:. If the voltage at the Non-Inverting Terminal pin 2 is higher than the Inverting Terminal pin 2the output pin 7 datashset also be high else the output will be low. Message 2 of 5. datashdet

Multisim and Ultiboard

Message 1 of 5. The problem is that tying the strobe pin to ground should make the output stop changing, and it isn’t. Submitted by admin on 6 March I expect the output to oscillate between 0 and 1 at the “zero crossing” of the signal.

  MAGICK OF CHANT O MATICS PDF

All of those comparator outputs should be a high state which means the LED will turn on connected through the 1K resistor to Vcc.

Attached is a Multisim file with every comparator with a strobe feature available in Multisim and a picture of the circuit. LMN Comparator with Strobe. Message 3 of 5.

LMN STMicroelectronics | Ciiva

Could the component model be the issue? Message 4 of 5. Any Op-Amp can be made to work as a voltage comparator, but the LM proves itself to be advantages by housing an Output Transistor inside its package. As grounding unused pins is a practice on electronics, I guess it was the way of the designer to make sure the device was not disabled for a dahasheet wired to that pin.

The problem is that the strobe pin is not working for the model. I tried adding in a transistor with a 1k resistor lk311n ground and a TTL signal at the base as per the datasheet and this doesn’t disable the output either.

The LM can work on a Single supply voltage or in a dual supply mode. TL — Programmable Reference Voltage.